Hlavním cílem práce je úprava pohybových os laserového stroje dostupného v laboratoři KSA. Hlavním úkolem je zvýšit rychlost posuvu stávajícího laserového stroje a odstranit problém s vibracemi. V prvé řadě byla provedena důkladná a podrobná studie pohonných mechanismů, které lze použít na laserových řezacích strojích, a vyhotoven přehled různých laserových strojů na trhu. Na základě tohoto průzkumu byly vytvořeny dvě možné varianty, z nichž jedna je zlepšení stávajícího typu pohonu (kuličkového šroubu) úpravou parametrů, které nám pomohou dosáhnout požadovaného posuvu, a druhou je změna celého typu pohonu (lineární motor). V závěru bylo po důkladné analýze těchto typů pohonů zvoleno optimální řešení pomocí dvou typů pohonů.
Anotace v angličtině
The main aim of the thesis is to enhance the motion axes of a laser machine which is available in the KSA laboratory. The major problem to overcome is to improve the feed rate of existing laser machine and cut down vibration problem. To overcome this, a detailed study of drive mechanisms which can used on laser cutting machines and an overview of different laser machines in the market has been thoroughly studied. From this research, two possible variants were considered, one of which is about enhancing the existing drive type (ball screw) by working on the parameters which will help us achieve the required feed rate and the other one is the change of whole drive type (linear motor). Finally, an optimum solution out of the two drive types has been chosen after thorough analysis of these drive types.
Klíčová slova
Laser, laserový řezací stroj, lineární pohony, pohon s kuličkovým šroubem, pohon s lineárním motorem, rychlost posuvu, zrychlení, průměr, stoupání.
Klíčová slova v angličtině
Laser, Laser Cutting machine, linear drives, ball screw drive type, Linear motor drive type, Feed rate, acceleration, diameter, pitch.
Rozsah průvodní práce
77 p. (12653), 2 p.
Jazyk
AN
Anotace
Hlavním cílem práce je úprava pohybových os laserového stroje dostupného v laboratoři KSA. Hlavním úkolem je zvýšit rychlost posuvu stávajícího laserového stroje a odstranit problém s vibracemi. V prvé řadě byla provedena důkladná a podrobná studie pohonných mechanismů, které lze použít na laserových řezacích strojích, a vyhotoven přehled různých laserových strojů na trhu. Na základě tohoto průzkumu byly vytvořeny dvě možné varianty, z nichž jedna je zlepšení stávajícího typu pohonu (kuličkového šroubu) úpravou parametrů, které nám pomohou dosáhnout požadovaného posuvu, a druhou je změna celého typu pohonu (lineární motor). V závěru bylo po důkladné analýze těchto typů pohonů zvoleno optimální řešení pomocí dvou typů pohonů.
Anotace v angličtině
The main aim of the thesis is to enhance the motion axes of a laser machine which is available in the KSA laboratory. The major problem to overcome is to improve the feed rate of existing laser machine and cut down vibration problem. To overcome this, a detailed study of drive mechanisms which can used on laser cutting machines and an overview of different laser machines in the market has been thoroughly studied. From this research, two possible variants were considered, one of which is about enhancing the existing drive type (ball screw) by working on the parameters which will help us achieve the required feed rate and the other one is the change of whole drive type (linear motor). Finally, an optimum solution out of the two drive types has been chosen after thorough analysis of these drive types.
Klíčová slova
Laser, laserový řezací stroj, lineární pohony, pohon s kuličkovým šroubem, pohon s lineárním motorem, rychlost posuvu, zrychlení, průměr, stoupání.
Klíčová slova v angličtině
Laser, Laser Cutting machine, linear drives, ball screw drive type, Linear motor drive type, Feed rate, acceleration, diameter, pitch.
Zásady pro vypracování
1. Introduction to the construction of a laser machine in KSA laboratories.
2. Basic control calculations of motion axes with currently used components.
3.Propose changes for possible increase of feed rates and acceleration of individual axes.
4.Design of a different drive unit for axis movement than the one currently in use.
Zásady pro vypracování
1. Introduction to the construction of a laser machine in KSA laboratories.
2. Basic control calculations of motion axes with currently used components.
3.Propose changes for possible increase of feed rates and acceleration of individual axes.
4.Design of a different drive unit for axis movement than the one currently in use.
Seznam doporučené literatury
[1] BUDYNAS, R. G. and J. K. NISBETT. Shigleys Mechanical Engineering Design (in SI Units). 10th ed. Asia: McGraw-Hill, 2015, 1104 p. ISBN 978-981-4595-28-5.
[2] MAREK, J. et al. Design of CNC Machine Tools. Praha: MM publishing, 2015, 730 p. ISBN 978-80-260-8637-6.
[3] HIWIN, online catalogues, https://www.hiwin.com/index.html
Seznam doporučené literatury
[1] BUDYNAS, R. G. and J. K. NISBETT. Shigleys Mechanical Engineering Design (in SI Units). 10th ed. Asia: McGraw-Hill, 2015, 1104 p. ISBN 978-981-4595-28-5.
[2] MAREK, J. et al. Design of CNC Machine Tools. Praha: MM publishing, 2015, 730 p. ISBN 978-80-260-8637-6.
[3] HIWIN, online catalogues, https://www.hiwin.com/index.html
Přílohy volně vložené
CAD drawings
Přílohy vázané v práci
ilustrace
Převzato z knihovny
Ano
Plný text práce
Přílohy
Posudek(y) oponenta
Hodnocení vedoucího
Záznam průběhu obhajoby
Průběh obhajoby je zveřejněn pouze přihlášenému uživateli.